Moulded Parts and Fittings

Hard plastic C-shaped clips which snap onto the spar next to other frame fittings to hold them firmly in the right position. Can be glued in place.

Priced by size (price includes VAT at 15%)

Pliable rubber grommet as used on Flexifoil power kite spars. The grommet is fitted onto the spar before the end cap is glued on, and keeps the flying line in position at the end of the spar.

Fits Flexifoil Spar (4.0mm)

Soft, pliable cap which fits over the end of a spar to prevent wear and damage to the kite fabric when inserted into a pocket or the nose of a kite.
Sourced from various suppliers depending upon price and availability, therefore colours may vary.

Priced by size (price includes VAT at 15%)

Firm rubber end cap as used on Flexifoil power kite spars. This cap is glued onto the tip of the spar. The flying line is attached between the grommet and the cap

Assorted rigid caps with end slots. These fittings are glued to the end of a spar, along which the sail is tensioned with cord or bungee at the split end.
These nocks are sourced from various suppliers (Exel, HQ, Dura), therefore the shape may vary
slightly from the image shown.

Priced by size (price includes VAT at 15%)

Rigid plastic spar caps with flat closed end and either a hole or side slot for sail tension cords. The smooth end prevents lines from catching and helps prevent the wing tip from digging into the ground.

Priced by size (price includes VAT at 15%)

Rigid stand-off connector which is glued on to the end of the stand-off, then hooked through a small reinforced hole in the trailing edge of the kite.

Fits 2.5mm stand-off

Rigid stand-off connector which is glued on to the end of the stand-off then pushed through a small reinforced hole in the trailing edge of the kite

Priced by size (price includes VAT at 15%)

Soft plastic clip which folds over the edge of the sail and fits flush against the fabric. The stand-off fits into the cap and is usually glued in place.

Priced by size (price includes VAT at 15%)

Rigid plastic connector which joins two spars together at a 90 degree angle to form a T shape. The smaller stand-off spar is glued into the hole in the base and the top clamps on and off the lower spreader.

Priced by size (price includes VAT at 15%)

Rigid plastic connector which joins two spars together at a 90 degree angle to form a T shape. The smaller stand-off spar is glued into the hole in the base and the top clamps on and off the lower spreader

Priced by size (price includes VAT at 15%)

Firm, flexible connector which joins two spars together at a 90 degree angle to form a T shape. The smaller stand-off spar fits into the hole in the base and the spreader is inserted into the larger hole.

Priced by size (price includes VAT at 15%)

Soft, pliable connector which joins two spars together at a 90 degree angle to form a T shape. These connectors will accommodate smaller stand-offs which have been fitted with an end cap.

Priced by size (price includes VAT at 15%)

Rigid plastic connector for joining three spars together at 90 degree angles to form the shape of a T.

Soft rubber connector for joining two spars together at a 45 degree angle.
Mixed size combinations.

Priced by size (price includes VAT at 15%)

Soft rubber connector for joining two spars together at a 45 degree angle.

Priced by size (price includes VAT at 15%)

Firm, flexible connector for joining two spars together at a 45 degree angle.

Priced by size (price includes VAT at 15%)

Rigid plastic connector for joining three spars together at 90 degree angles to form a cross.
Sourced from various suppliers, therefore the shape may vary slightly from the image shown.

Priced by size (price includes VAT at 15%)

Machined fitting to join two or three spars together at
90 degrees to form a cross. Includes aluminium ferrule for fitting the spreader spar into.
Fitting requires Allen key.

Priced by size (price includes VAT at 15%)

Machined fitting to join two or three spars together at
90 degrees to form a cross. Includes machined plastic locating sleeve and internal carbon ferrule.
Fitting requires Allen key.
Fits G-Force & Skinny spars.

Priced by size (price includes VAT at 15%)

Machined fitting to join two or three spars together at
90 degrees to form a cross. Fitting requires Allen key
Supplied without ferrule
6.0mm vertical hole & 8.0mm horizontal hole.

Rigid connector used to join two spars together to form the shape of a cross

Rigid connector for joining three spars together at an angle to form an angled cross (keel).
Normally used on Eddy/Diamonds

Priced by size (price includes VAT at 15%)

Soft and stretchy bands which are ideal for tensioning sails when used with a wing tip nock.

Flexible O-rings which can be twisted around two intersecting spars to hold them together in the
shape of a cross.
17.0mm o.d. x 11.0mm i.d.

Rigid moulded polypropylene triangular ring ideal for using with webbing for straps.
40mm along flat edge (outside)
28mm along flat edge (inside)

Rigid moulded buckle fitting designed for adjusting the length of straps.
Fits 25mm webbing strap.
30mm external length
25mm internal length

Rigid moulded buckle fitting designed for adjusting the length of straps.
Fits 25mm webbing strap.
30mm external length
25mm internal length

Rigid moulded swivel hook for shoulder strap attachments
Fits 38mm webbing strap.

These black nylon locks feature an internal spring and lock on to cords up to 5mm diameter, preventing the cord from retracting into garment seams or enclosures.
Ideal for outdoor applications.